How do I setup Layer 3 routing on my DGS-3324SR/DGS-3324SRi/DXS-3350SR and DXS-3326GSR?
Warning:
The example configuration below was created from a factorydefault configuration on theDGS-3324SR/DGS-3324SRi/DXS-3350SR/DXS-3326GSR switches. Werecommend saving your current configuration.
Scenario:
Applies to: DGS-3324SR, DGS-3324SRi, DXS-3350SR, andDXS-3326GSR
This example shows a simple Layer 3 configuration on astandalone DGS-3324SR switch. The different IP networks can berouted without any Layer 3 routing protocols enabled on the switch.In this scenario, the DGS-3324SR will create 4 local routes in theRouting Table. The traffic going between the different subnets willbe routed based on the information found in the Local Routing tablein the switch.
Switch Configuration:
Step 1 Connect to the switch using the consoleconnection with your preferred Terminal emulation software.
Step 2 Once connected to the CLI, login at theusername and password prompt. The default is username is<blank> and password is <blank>.
Step 3 At the prompt, enter the followingcommand:
reset system
Select 'y' when prompted to confirm the factory reset. Theswitch will now reboot with the factory default settings.
Step 4 Login again to the switch.
Step 5 Once at the CLI, type in the followingcommands to create the VLANs and IP interfaces associated with eachVLAN.
config vlan default delete 1:1-1:24
create vlan v101 tag 101
config vlan v101 add untagged 1:1-1:6
create ipif net1 192.168.1.254/24 v101 state enabled
create vlan v102 tag 102
config vlan v102 add untagged 1:7-1:12
create ipif net2 192.168.2.254/24 v102 state enabled
create vlan v103 tag 103
config vlan v103 add untagged 1:13-1:18
create ipif net3 192.168.3.254/24 v103 state enabled
create vlan v104 tag 104
config vlan v104 add untagged 1:19-1:24
create ipif net4 192.168.4.254/24 v104 state enabled
save
Step 6 Configure the PCs in each subnet withthe appropriate IP address and gateway. For example,
Net1 PC - 192.168.1.10/255.255.255.0 gateway 192.168.1.254
Net2 PC - 192.168.2.10/255.255.255.0 gateway 192.168.2.254
Net3 PC - 192.168.3.10/255.255.255.0 gateway 192.168.3.254
Net4 PC - 192.168.4.10/255.255.255.0 gateway 192.168.4.254
Testing the Configuration:
1. Net1 PC can ping gateway (192.168.1.254), other DGS-3324SRinterfaces (192.168.2.254, 192.168.3.254, etc) and other network'sPC.
2. Net2 PC can ping gateway (192.168.2.254), other DGS-3324SRInterfaces (192.168.1.254, 192.168.3.254, etc) and other network'sPC IP.
3. Same testing for Net3 PC, Net4 PC.
Verifying the Configuration:
Below is a list of commands that can be used to verify theconfiguration and are useful for diagnostics:
1. show vlan
2. show ipif
22 Други потребители намират това за полезно.
Беше ли това полезно за Вас?22 Други потребители намират това за полезно.
Благодарим Ви за обратната връзка.
Съжаляваме, че не успяхме да помогнем! Натиснете тук за повече Въпроси и отговори или за да отидете в секция Поддръжка.